Technical Talk
-
- Posts: 5
- Joined: Thu Jul 20, 2017 11:56 am
Re: Technical Talk
yes i knew about the 'glare shield' and have already made the instrument panel, now i can paint it black, i just wanted to know i was doing it right. the instrument panel in 1/10 scale measures in at 40mm wide x 27mm high with 6mm dial diameter.
- Renegadenemo
- Posts: 4750
- Joined: Mon Dec 01, 2008 12:29 pm
- Location: N E England
- Contact:
Re: Technical Talk
I hope you mean a quarter-inch and not this base-ten nonsense evolved for people who can't count to twelve!with 6mm dial diameter
I'm only a plumber from Cannock...
"As to reward, my profession is its own reward;" Sherlock Holmes.
I have wrought my simple plan
If I give one hour of joy
To the boy who’s half a man,
Or the man who’s half a boy.
Sir Arthur Conan Doyle.
"As to reward, my profession is its own reward;" Sherlock Holmes.
I have wrought my simple plan
If I give one hour of joy
To the boy who’s half a man,
Or the man who’s half a boy.
Sir Arthur Conan Doyle.
-
- Posts: 78
- Joined: Fri Mar 30, 2012 12:17 pm
- Location: Worcestershire
Re: Technical Talk
or as the O/D of that most British of metric screw threads 0 BARenegadenemo wrote: ↑Sat Jul 22, 2017 2:00 amI hope you mean a quarter-inch and not this base-ten nonsense evolved for people who can't count to twelve!with 6mm dial diameter
- Renegadenemo
- Posts: 4750
- Joined: Mon Dec 01, 2008 12:29 pm
- Location: N E England
- Contact:
Re: Technical Talk
Ah, but the BA standard isn't British. It's Swiss or Swedish or some such, where people can't count to twelve.
I'm only a plumber from Cannock...
"As to reward, my profession is its own reward;" Sherlock Holmes.
I have wrought my simple plan
If I give one hour of joy
To the boy who’s half a man,
Or the man who’s half a boy.
Sir Arthur Conan Doyle.
"As to reward, my profession is its own reward;" Sherlock Holmes.
I have wrought my simple plan
If I give one hour of joy
To the boy who’s half a man,
Or the man who’s half a boy.
Sir Arthur Conan Doyle.
Re: Technical Talk
Correct me if I am wrong, but I always understood, and was always taught that, BA stood for "British-Association".
Was I misled?
Editied because I typed "British-Armstrong" in place of "British Association".
Was I misled?
Editied because I typed "British-Armstrong" in place of "British Association".
Just cos my username is Thunderer, doesn't necessarily mean I SHOUT !!
"A vehicle is designed to be used, restored or otherwise" A personal response on the question "you have just restored it, why use it?"
"A vehicle is designed to be used, restored or otherwise" A personal response on the question "you have just restored it, why use it?"
- Renegadenemo
- Posts: 4750
- Joined: Mon Dec 01, 2008 12:29 pm
- Location: N E England
- Contact:
Re: Technical Talk
You're right enough but we nicked it from the Swiss watchmakers - at least that's what one of my lecturers told me many years ago.Correct me if I am wrong, but I always understood, and was always taught that, BA stood for "British-Association".
I'm only a plumber from Cannock...
"As to reward, my profession is its own reward;" Sherlock Holmes.
I have wrought my simple plan
If I give one hour of joy
To the boy who’s half a man,
Or the man who’s half a boy.
Sir Arthur Conan Doyle.
"As to reward, my profession is its own reward;" Sherlock Holmes.
I have wrought my simple plan
If I give one hour of joy
To the boy who’s half a man,
Or the man who’s half a boy.
Sir Arthur Conan Doyle.
Re: Technical Talk
British Association screw threads, or BA screw threads, are a largely obsolete set of small screw threads, the largest being 0BA at 6 mm diameter. They were, and to some extent still are, used for miniature instruments and modelling.
They are unusual in that they were probably the most "scientific" design of screw, starting with 0BA at 6.0mm diameter and 1.0mm pitch and progressing in a geometric sequence where each larger number was 0.9 times the pitch of the last size. They then spoiled this by rounding to 2 significant figures in metric and then converting to inches and rounding to the thousandth of an inch. This anticipated worldwide metrication by about a century. The design was first proposed by the British Association in 1884[1][2] with a thread angle and depth based on the Swiss Thury thread,[3] it was adopted by the Association in 1903.
The Thury thread was different in that it went both positive and negative all the way up to a size of -20 which was 75.2mm diameter by 8.23mm pitch. The Thury numbers were rounded to three significant figures. The Thury thread form had the crests rounded at 1/6p and the roots rounded at 1/5p so the thread angle was close to 47.5 degrees but not exactly. This was simplified in the BA thread definition by defining the thread angle to be 47.5 degrees exactly and the thread form to be symmetrical with a depth of 0.6p.
The British Standards Institution recommends the use of BA sizes in place of the smaller British Standard Whitworth (BSW) and British Standard Fine (BSF) thread screws (those below 1/4").[4]:4 Generally, the 0BA size was dropped in place of 7/32" BSF in assemblies that included larger fasteners, however, in smaller equipment that was primarily electronic/electrical the 0BA size would typically be used in place of the BSF or BSW screw where it was the largest size required.
BA threads are still used in some precision instruments, such as optics and moving-coil meters, relays etc. A 2BA thread is used to connect the head of a dart to its shaft — as such, it is one of the few common uses of this thread in North America.
2BA threads are commonly found in the old imperial BESA (British Engineering Standards Association) conduit boxes in the UK which are still in use (but not installed) today.
Wikipaedia
They are unusual in that they were probably the most "scientific" design of screw, starting with 0BA at 6.0mm diameter and 1.0mm pitch and progressing in a geometric sequence where each larger number was 0.9 times the pitch of the last size. They then spoiled this by rounding to 2 significant figures in metric and then converting to inches and rounding to the thousandth of an inch. This anticipated worldwide metrication by about a century. The design was first proposed by the British Association in 1884[1][2] with a thread angle and depth based on the Swiss Thury thread,[3] it was adopted by the Association in 1903.
The Thury thread was different in that it went both positive and negative all the way up to a size of -20 which was 75.2mm diameter by 8.23mm pitch. The Thury numbers were rounded to three significant figures. The Thury thread form had the crests rounded at 1/6p and the roots rounded at 1/5p so the thread angle was close to 47.5 degrees but not exactly. This was simplified in the BA thread definition by defining the thread angle to be 47.5 degrees exactly and the thread form to be symmetrical with a depth of 0.6p.
The British Standards Institution recommends the use of BA sizes in place of the smaller British Standard Whitworth (BSW) and British Standard Fine (BSF) thread screws (those below 1/4").[4]:4 Generally, the 0BA size was dropped in place of 7/32" BSF in assemblies that included larger fasteners, however, in smaller equipment that was primarily electronic/electrical the 0BA size would typically be used in place of the BSF or BSW screw where it was the largest size required.
BA threads are still used in some precision instruments, such as optics and moving-coil meters, relays etc. A 2BA thread is used to connect the head of a dart to its shaft — as such, it is one of the few common uses of this thread in North America.
2BA threads are commonly found in the old imperial BESA (British Engineering Standards Association) conduit boxes in the UK which are still in use (but not installed) today.
Wikipaedia
- Renegadenemo
- Posts: 4750
- Joined: Mon Dec 01, 2008 12:29 pm
- Location: N E England
- Contact:
Re: Technical Talk
Absolutely cracking doco here for anyone interested in metal shaping.
https://www.youtube.com/watch?v=b4haVtIP2M8
https://www.youtube.com/watch?v=b4haVtIP2M8
I'm only a plumber from Cannock...
"As to reward, my profession is its own reward;" Sherlock Holmes.
I have wrought my simple plan
If I give one hour of joy
To the boy who’s half a man,
Or the man who’s half a boy.
Sir Arthur Conan Doyle.
"As to reward, my profession is its own reward;" Sherlock Holmes.
I have wrought my simple plan
If I give one hour of joy
To the boy who’s half a man,
Or the man who’s half a boy.
Sir Arthur Conan Doyle.
Re: Technical Talk
It wont load Bill - looks like the link has been closed downRenegadenemo wrote: ↑Thu Oct 12, 2017 12:57 amAbsolutely cracking doco here for anyone interested in metal shaping.
https://www.youtube.com/watch?v=b4haVtIP2M8
When you come to a fork in the road, take it